More info & order page |
|
|
Powered by a standard 12V lawn tractor battery the KartRaiser will lift and lower your kart all day long at the track. Designed for karts weighing up to 340 lbs*** with the standard CIK rear bumper system. An adjustable front support enables changes to be made to accommodate different rear bumper heights, keeping your kart level. ***For kart in access of 240lbs please let us know so we can make the mods
necessary to lift the extra weight. For bumpers other than the standard CIK type give us a call, we will
work with you to solve you kart raising problems. This includes Quarter midget,
Jr. champ and Superkarts etc. ! I will ship internationally, although it
tends to be expensive.
Expected time before shipping
If order is placed today 53
- 5 business days 716 - 860 - 2703 1- 6 days Remember to add the tray below if
want one 1- 6 days Remember to add the tray below if
want one Specialty colors other than standard colors $30 The Silver
Vein will be the standard color for our KartRaiser's
from now on. I will produce limited quantities of the other standard
colors as time allows. Red, Black and Blue will be available as time
permits Optional color choices:
Read
all material including safety sheet Thank you for your
interest in the KartRaiser from Full Bore Karting. We believe this stand will
put some needed relief into your pit area and race days. Your
unit has been covered with some insulation to aid in its protection during
shipping. The long piece on the front lift arm has been secured and should
remain in place. In the bag you will find washers, axle collars and an Allen
wrench for the wheels. You
will need a standard U1L size lawn tractor battery with 160 CCA to operate this
unit. A dry cell battery of at least 160 CCA and no larger than 5” x 8” will
fit in the battery tray as well. ***Keeping
tension on the cable at all times will avoid the cable from loosening on the
spool and pinching itself. If this occurs you will need to release some cable
and re wind it on the spool This can be accomplished by releasing the spool with
the handle on the end, pull out the cable. Reset the handle and use the winch to
pull in the cable, keeping tension on it and guiding it on the spool in an even
fashion*** You
might notice some stiffness in the bushings on the lift arm when new. These
should loosen up quickly. It
might be necessary to manually push forward the arms to lower the stand for the
first few inches of movement. Some weight has been added to the top front lift
arm to avoid this. The
cable guide on the wheel should be moved up after unpacking, DO THIS WITH THE
STAND IN THE UP POSITION TO AVOID BINDING AGAINS THE CABLE. When
lowering the kart you will need to lightly pull back the stand as the karts nose
touches down to keep the cable tight. This can be done with the control cable or
by placing your foot on the rear wheel and rotating it backwards a half turn.
Gravity will take over after that. **For
swivel wheeled models, pull the stand back a foot or so before lowering the kart
to set the swivels in the correct position. Then raise the arms before moving
stand away from kart. Push the KartRaiser forward behind your kart to set wheels
before lowering the arms to lift your kart. You will understand why the first
time you forget :-) Enjoy
your new KartRaiser Electric Kart lifter! Watch
the stand as it lifts. When the arms make contact with the stops release the
control button. When the tone of the motor changes STOP!!! Excessive tension
applied to the lift at this point will cause damage!!!!!!!!!!!!!! Although
the cable and motor drive are rated at 2000lbs do not stand directly in line
(behind) the Take
care of your stand and it will take care of you! Check fasteners periodically for tightness, Lube
wheel bearings. Watch and keep small animals and children away from
stand while in operation. If
at and time the cable becomes frayed, seek a qualified technician or repair shop
to shorten and reinstall the hook, loop and compression sleeves. There is plenty
of extra cable. DO NOT ATTEMPT TO USE SADDLE CLIPS for repair !! Or
contact us for a replacement Transportation
stand instructions I have upgraded the chain connectors on the transportation
stands. The chains will hold 500lbs (250ea.),
more than enough for transporting your kart. Use the winch to get the holes for the rear bar lined up.
You might be putting some slight pressure on the stand, and that is perfectly
normal. Secure the kart and stand in the trailer in a manner so as not to let
the kart come out of the rear pickup hooks. Generally, secure the rear of the
kart in the stand via the included strap, and strap the stand to the trailer. In
front you can strap the kart to the trailer.
|
|
Send mail to webmaster@kartraiser.com with
questions or comments about this web site.
|